____________________

engine overhaul
There are different ways of overhauling an engine. Most workshops do what is called an in-chassis rebuild. This is where you don't remove the engine from the car, you just pull what you need to do the job of it and do a minor overhaul - replace the cylinder liners, pistons (if they need it), piston rings, replace the big end and crankshaft bearings, lap the valves in and replace the valve stem seals, strip and check the oil pump, replace the gaskets and seals Just what is needed to be done to bring the engine back to factory specification and performance.

A major overhaul or out-of chassis rebuild is much more thorough. The engine is removed from the car (obviously) and totally stripped down - every nut and bolt are removed, cleaned, checked. Most moving parts are replaced with brand new factory stock parts - often the only original parts of an engine that has been MO'ed are the block casting, the head casting, the crankshaft, conrods, flywheel and camshaft. If any of those aren't in serviceable condition they get switched out too. And the motor gets a fresh paint job. A MO is much more expensive, but it's like you get a brand new engine back, while still usually costing less than actually buying a brand new engine.

Then there is the process of 'blueprinting' an engine. This is a MO, but much more detailed. There are manufacturing tolerances that mean there can be slight differences between two parts that essentially are the same. They are the same, only not quite. Blueprinting fixes that. All the parts that are supposed to be the same, are exactly the same. Conrods and pistons are weight matched and balanced. The crankshaft is also perfectly balanced, instead of "close enough is good enough". When you replace bearings with stock parts, once again there are manufacturing tolerances. Some crankshaft and camshaft bearing journals are ever so slightly bigger or smaller than others and with stock bearings, this causes extra friction and slight loss of power. When you blueprint an engine, you custom fit bearings to each individual journal.

To put it simply, if you had two brand new engines, one factory stock, right off the test dyno at the assembly plant and just been finished 'running in', and one that had been "blueprinted" (but still stock, no aftermarket performance parts) by a performance workshop, and compared the two, the blueprinted motor would not only start easier, run quieter and smoother, but also use slightly less fuel, and make a little more horsepower. It would also be more responsive and rev quicker.

https://answers.yahoo.com/question/index?qid=20090101131023AA5EtJ2

turbo charger repairs

Ryan Auto Worx is a Turbo charger repairs Company based in Centurion.

Turbo charger repairs are carried out and supervised by fully qualified vehicle repairs personnel.
We pride ourselves in providing a speedy without compromising the quality of the service on your car.

Our Turbo charger repair services range from the smallest to the largest 2 stroke marine diesel engines.

For more information regarding Turno charger repair, give us a call on 012 940 2104

clutch disk services in centurionA number of drivers are aware of how to operate clutch and brake systems in cars, but not a lot of drivers will know when the brake and clutch systems need urgent attention. The easiest signs to look out for in understanding that your clutch needs servicing are :

1) Your gear will have a tendency to disengage (This means your clutch needs attention)
2) Unusual Oil leakages (Gives you an indication your clutch is out)
3) Hydraulic leakages

If you pick up any of the signs above, feel free to  give us a call and we will be happy to service your car

vehicle services in PretoriaRyan Autoworx is a vehicle services and repair company in Pretoria. Our vehicle services amongst others include:

  • Computer diagnostics and electrical fault finding
  • Steering and suspension systems
  • Brake and clutch systems
  • Turbocharger repairs/refurbishing
  • Engine overhauls
  • Petrol Fuel Injection Systems
  • 4x4 Fitments, repairs and modifications

For More information about our services, contact Ryan's Auto Worx on 012 940 2104